#MASTERCAM X5 TRAINING TUTORIAL PDF MANUAL#
#MASTERCAM X5 TRAINING TUTORIAL PDF SOFTWARE#
#MASTERCAM X5 TRAINING TUTORIAL PDF WINDOWS#

You may be required to use the Misc Values. For instance: You may be required to position your stock in machine space rather than at Mastercam's origin. Your post processor may require certain additional programming information not covered in this tutorial. Contact your Mastercam reseller to request post processor services such as multi-axis post development. There are no default 5-Axis post processors included with Mastercam due to the variation in multi-axis machine configurations. To apply these toolpaths to a 5-Axis machine tool, a customized post processor for your machine is required.

This tutorial covers Mastercam's 5-Axis toolpath functionality. This tutorial takes approximately two hours to complete.

!Running the Machine simulation to detect collisions between the stock, tool and any machine components. !Running the Verify to simulate the tool cutting from the solid model. !Running the Backplot to see the path the tool takes to cut the part. The Student will simulate the toolpaths using Mastercam's Verify and Backplot by: !Defining a 3-dimensional shape the size of the work piece. !Create Transform Rotate toolpaths to machine the entire impeller. !Create a Parallel to multiple curves toolpath from the Wireframe toolpath family to finish the blade. !Switch to the advance interface and create a Parallel to surface toolpath to add multipasses the toolpath. !Create an Impeller blade swarf finish toolpaths from the Custom Application toolpath to semifinish one blade. !Finish the impeller floor using the same Morph between 2 surfaces toolpath. !Switch to the Advanced interface and create a Morph between 2 surfaces toolpath to add depth cuts and avoid gouging the blades. Objectives: The Student will create 5-Axis milling toolpaths consisting of: !Create a Impeller floor surface without tiltcurve toolpath from the Custom Application toolpath family to rough the area between two blades. TUTORIAL #4 ROUGH & FINISH IMPELLER WITHOUT TILTCURVE 4-1 Tutorial #5 Collision Control Strategies. 3-1 Tutorial #4 Rough & Finish Impeller Without Tiltcurve. 2-1 Tutorial #3 Finish Surfaces Toolpath. A-1 Tutorials Tutorial #1 Projection Toolpath.

#MASTERCAM X5 TRAINING TUTORIAL PDF WINDOWS#

Windows, Windows XP, Windows Vista and Windows NT are registered trademarks of Microsoft Corporation.ДЄdvanced Multiaxis Training Tutorial Contents Getting Started. Microsoft, the Microsoft logo, MS, and MS-DOS are registered trademarks of Microsoft Corporation N-See is a registered trademark of Microcompatibles, Inc. Trademarks Mastercam is a registered trademark of CNC Software, Inc. This document may not, in whole or part, be copied, photographed, reproduced, translated or reduced to any electronic medium or machine readable form without prior consent, in writing, from In-House Solutions Inc.

#MASTERCAM X5 TRAINING TUTORIAL PDF MANUAL#

Copyrights This manual is protected under International copyright laws. Some jurisdictions do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so the above limitation or exclusion may not apply to you. has been advised of the possibility of such damages. be liable for direct, indirect, or consequential damages resulting from any defect in the manual, even if In-House Solutions Inc. Should the manual prove defective following its purchase, the buyer (and not In-House Solutions Inc., its distributer, or its retailer) assumes the entire cost of all necessary servicing, repair, of correction and any incidental or consequential damages. manual is sold or licensed 'as is.' The entire risk as to its quality and performance is with the buyer.

#MASTERCAM X5 TRAINING TUTORIAL PDF SOFTWARE#

makes no warranties, either express or implied, with respect to this manual or with respect to the software described in this manual, its quality, performance, merchantability, or fitness for any particular purpose. Disclaimer Of All Warranties And Liability In-House Solutions Inc. reserves the right to make improvements to this manual at any time and without notice. All rights reserved Software: Mastercam X5 Author: Mariana Lendel ISBN: 978-1-92 Revision Date: November 3, 2010 Mastercam X5 Training Tutorials - Advanced Multiaxis Copyright: 1998 -2010 In-House Solutions Inc. To order more books: Call 1-80 or Visit or Contact your Mastercam dealer

Mastercam x5 training tutorial pdf